Etc Source Four HID User Manual

Browse online or download User Manual for Lighting Etc Source Four HID. ETC Source Four HID User Manual

  • Download
  • Add to my manuals
  • Print
  • Page
    / 8
  • Table of contents
  • BOOKMARKS
  • Rated. / 5. Based on customer reviews
Page view 0
Source Four™ HID • 1
Source Four
HID
Lamp type and general information:
Do not use lamps other than the following lamp type in Source Four HID fixtures.
Use of lamps other
than specified below will void UL/cUL safety compliance and your warranty
.
Source Four HID is suitable for damp locations
Can be canopy mounted
No recessed mounting
Caution!
Source Four HID is
NOT
dimmable. Dimming will damage ballast and void warranty.
Ballast information
Caution!
The Source Four HID
cannot
be dimmed.
Acceptable voltage is 120V (+/- 10%) 50/60HZ
only
.
Operating current of 1.5 Amps
Inrush current of <14 Amps
Room ambient temperature should not exceed 104ºF (40ºC)
Lamp ignition voltage is 4.5Kv, non-hot restrike.
Ballast case temperature should not exceed 167ºF (75ºC)
The ballast is attached to the Source Four yoke by two screws, non-remotable.
Lamp Type Manufacturing Codes Watts Base Bulb LCL Ave.
Hrs.
Initial
lumens
Color
temp
Ceramic Metal Halide
CDM-T 150W/830 150 G12 T6 56mm 9000 14000 3000˚K
CDM-T 150W/942 150 G12 T6 56mm 9000 12700 4000˚K
MD150T6/U/G12/830 150 G12 T6 56mm 9000 14000 3000˚K
MBI150/T/30 150 G12 T7 57mm 6000 11500 3000˚K
MBI150/T/40 150 G12 T7 57mm 6000 11250 4000˚K
Table 1:
HID lamp reference
Beam focus knob
Lens tube
Shutters
Barrel
Pattern holder slot
Retainer bolt
Drop-in iris
Retaining clip
Color frame
Color frame holder
Reflector housing
Yoke locking knob
Lamp housing
Ballast
Barrel rotation knob
Yo ke
Page view 0
1 2 3 4 5 6 7 8

Summary of Contents

Page 1 - Source Four

Source Four™ HID • 1 Source Four ™ HID Lamp type and general information: Do not use lamps other than the following lamp type in Source Four HID

Page 2 - Focusing the beam

2 • Source Four™ HID Installing or replacing the lamp A lamp must be installed before you use the fixture. Note: Verify that the lamp you intend

Page 3 - Shaping the beam

Source Four™ HID • 3 Color frame retaining clip The color frame holder is equipped with a spring-loaded retaining clip that prevents color frames

Page 4 - 4 • Source Four™ HID

4 • Source Four™ HID Rotating the barrel assembly 1. Loosen the barrel rotation knob directly behind the shutters on the underside of the reflector

Page 5 - Lens locations

Source Four™ HID • 5 Cleaning ETC offers the following recommendations when cleaning and inspecting lenses and reflectors: Do not use glass or w

Page 6 - Cleaning the reflector

6 • Source Four™ HIDCleaning the reflectorTo quickly clean the reflector, remove the lens tube and clean the dust from the reflector with a blast of o

Page 7 - Source Four™ HID • 7

Source Four™ HID • 7

Page 8 - Electronic Theatre Controls

Electronic Theatre ControlsNorth America 3030 Laura Lane • Middleton, Wisconsin 53562 • USA • Tel: (+1) 608 831 4116 • Fax: (+1) 608 836 1736Europe

Comments to this Manuals

No comments